- -35%

This TP4056 1A Li-ion lithium Battery Charging Module with Circuit Protection – Micro USB is a tiny module, perfect for charging single cells that don’t have their own protection circuit. Based on the TP4056 charger IC and DW01 battery protection IC this module will offer 5V 1A charge current then cut off when finished.
Furthermore when the battery voltage drops below 2.4V the protection IC will switch the load off to protect the cell from running at too low of a voltage – and also protects against over-voltage and reverse polarity connection (it will usually destroy itself instead of the battery) however please check you have it connected correctly the first time.
Each module is tested OK before shipment so it has high reliability for the best performance. In conclusion, it is special design for a single lithium battery charging. Other features include the current monitor, under voltage lockout, automatic recharge, and two status pin to indicate charge termination and the presence of an input voltage.
Using the module:
FEATURES
Package Contents :
1 X Lithium Battery Charging Board with circuit Protection Module
NOTE :Use mature charging chip TP4056 for simple peripheral circuits, good protection performance, and high charging accuracy.
This TP4056 1A Li-ion lithium Battery Charging Module – Micro USB is a tiny module, perfect for charging single cells. Based on the TP4056 charger IC this module will offer 5V 1A charge current.
With Mini-USB onboard connector, you can directly connect to computer USB port for battery charging. If USB is not available you can use an external source voltage at IN+/IN- pads, it is great for DIY projects. It is small size and lightweight.
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
AMS1117-1.2V, 1A, Voltage Regulator IC is a series of low dropout three -terminal regulators with a dropout of 1.2V at 1A load current. AMS 1117 features a very low standby current 2mA.
AMS 1117 offers thermal shut down and current limit functions, to assure the stability of chip and power system. And it uses a trimming technique to guarantee output voltage accuracy within 2%. Other output voltage accuracy can be customized on demand, such as 1%
It is an 8 Channel Isolated 28V 10A Relay Module, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc. It is also able to control various appliances and other types of equipment with large current. Relay output maximum contact is AC250V 10A and DC 28V 10A. One can connect a microcontroller with standard interface directly to it. Red working status indicator lights are conducive to the safe use.
This Relay is used for wide variety of AC & DC applications like Home Automation configured, Solenoids, Motors, lights, fans, heavy load device, home appliances & controlling higher current loads from microcontroller development board.
These Jumper Wires are great for creating circuits between your microcontroller and the breadboard on the bots Reusable for fast build a prototype of an electronic circuit. Soldering is not required.
Wires are flexible, durable, reusable, easy to trace, easy to connect and disconnect.
With these Jumper wires you can modify or revise the circuits easily.
AMS1117-1.8V, 1A, Voltage Regulator IC is a series of low dropout three -terminal regulators with a dropout of 1.8V at 1A load current. AMS 1117 features a very low standby current 2mA.
AMS 1117 offers thermal shut down and current limit functions, to assure the stability of chip and power system. And it uses a trimming technique to guarantee output voltage accuracy within 2%. Other output voltage accuracy can be customized on demand, such as 1%
ESP32 is a series of low-cost, low-power system on a chip microcontrollers with integrated Wi-Fi and dual-mode Bluetooth. The ESP32 series employs a Tensilica Xtensa LX6 microprocessor and includes built-in antenna switches, RF balun, power amplifier, low-noise receive amplifier, filters, and power-management modules. It is a successor to the ESP8266 microcontroller.
PIR infrared sensor module is based on infrared technology. High sensitivity, high reliability, low power consumption, low voltage operation mode. It’s Compatible with ARDUINO, RASPBERRY PI, AVR, PIC, 8051, etc. Widely used in various auto-sensing electrical equipments for security, automation and lighting control systems because of its unique property of detecting the movement of infrared emitting objects like human bodies. This sensor is equipped with Fresnel lens for improving the detection pattern. All you have to do is give the supply voltage and leave for about a minute to stabilize. Any movement detection causes the sensor output to go high (3.3V). This sensor can be easily used for 220V automatic lighting systems with the help of a simple relay circuit.
This TP4056 1A Li-ion lithium Battery Charging Module with Circuit Protection – Micro USB is a tiny module, perfect for charging single cells that don’t have their own protection circuit. Based on the TP4056 charger IC and DW01 battery protection IC this module will offer 5V 1A charge current then cut off when finished.
Furthermore when the battery voltage drops below 2.4V the protection IC will switch the load off to protect the cell from running at too low of a voltage – and also protects against over-voltage and reverse polarity connection (it will usually destroy itself instead of the battery) however please check you have it connected correctly the first time.