- -10%

These Jumper Wires are great for creating circuits between your microcontroller and the breadboard on the bots Reusable for fast build a prototype of an electronic circuit. Soldering is not required.
Wires are flexible, durable, reusable, easy to trace, easy to connect and disconnect.
With these Jumper wires you can modify or revise the circuits easily.
Features :
Package Includes :
4 x Flexible Male to Female Jumper Wires 20 cm
Heat Shrink Sleeve 10mm are excellent for insulation. They have exceptional insulation characteristics, excellent stress control properties; long-term weather and regular wear and tear resistance, ease of installation and reliable performance in even in harshest of the situations.
These High performance 2:1 heat shrink material tubes, bundles, and protects cables; wire and hoses are used for a wide range of DIY applications. It is used extensively for cable and wire harnessing, strain relief, insulation, color-coding, identification, and protection.
By Using The Adapter You can use Two SIM Cards and One Micro SD card at the same time Without Any Network Disturbances.
The SIM In The Adapter Reads The SIM As 2nd SIM And Support The Same Signal Bandwidth As Of SIM 2, Also Supports VoLTE.
The Adapter Is Super Flexible And Durable With A Thickness Of 0.1mm Which It Allows To Work With Multiple Folds.
A crystal oscillator is an electronic circuit or device which is used to generate a stable frequency with the help of a crystal instead of a tuned circuit. The crystal when vibrates, it acts like a resonator & as a result generates an oscillated frequency. The resonator circuit uses a crystal to generate the oscillation.
The 1N5819 is a Schottky Diode with forward voltage drop of 600mV and a forward current of 1A. Since it has a very low forward voltage drop it can be used in reverse polarity protection circuits, unlike a normal diode which has more than 1V as forward voltage drop 1N5819 only has 600mV drop across it when 1A current is flowing through it.
Compared to normal diodes Schottky diode also has relatively faster switching speeds and hence can be used in high frequency switching circuits. The reverse blocking voltage for 1N5819 is about 28V only which is kind of a downside for all Schottky diodes so make sure this does not affect the performance in your circuit.
It is an RM065 500 Ohm Trimpot Trimmer Potentiometer. The potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver.
It is an RM065 100K Ohm Trimpot Trimmer Potentiometer. The potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver.
0402 capacitor is Mounted either by flow or reflow soldering methods and gives excellent dielectric strength due to uniform structure of dielectric layers
It is an RM065 2K Ohm Trimpot Trimmer Potentiometer. The potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver.
AMS1117-1.8V, 1A, Voltage Regulator IC is a series of low dropout three -terminal regulators with a dropout of 1.8V at 1A load current. AMS 1117 features a very low standby current 2mA.
AMS 1117 offers thermal shut down and current limit functions, to assure the stability of chip and power system. And it uses a trimming technique to guarantee output voltage accuracy within 2%. Other output voltage accuracy can be customized on demand, such as 1%
It is an RM065 5K Ohm Trimpot Trimmer Potentiometer. The potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver.
A diode is a device which allows current flow through only one direction. That is the current should always flow from the Anode to cathode.
This is called a power diode because of its high forward current and reverse voltage with a power dissipation of 6.25W. For 1N5408 Diode, the maximum current carrying capacity is 3A it withstand peaks up to 200A. Hence we can use this in circuits that are designed for less than 3A. The reverse current is 10uA which is negligible. These diodes have a slow recovery time so in modern electronics it is being replaced by other advanced diodes.
12-0-12 3Amp Center Tapped Step Down Transformer is a general purpose chassis mounting mains transformer. Transformer has 230V primary winding and center tapped secondary winding. The transformer has flying colored insulated connecting leads ( Approx 100 mm long ). The Transformer act as step down transformer reducing AC - 230V to AC - 12V.
The Transformer gives outputs of 12V, 12V and 0V. The Transformer's construction is written below with details of Solid Core and Winding.
AMS1117-ADJ, 1A, Voltage Regulator IC is a series of low dropout three -terminal regulators with a dropout of adjustable voltage 1A load current. AMS 1117 features a very low standby current 2mA.
AMS 1117 offers thermal shut down and current limit functions, to assure the stability of chip and power system. And it uses a trimming technique to guarantee output voltage accuracy within 2%. Other output voltage accuracy can be customized on demand, such as 1%
Schottky diodes have very low forward drop voltage VF which makes them ideal for fast switching applications at lower current ratings. 1N5822 have forward voltage drop of minimum 0.525 V that is it requires 0.525 V to conduct in forward biased direction. The 1N5822 has maximum average forward rectified current IF(AV) of 3A. The maximum repetitive peak reverse voltage VRRM for 1N5822 is 40V.
It is an RM065 50K Ohm Trimpot Trimmer Potentiometer. The potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver.
Heat Shrink Sleeve 8mm are excellent for insulation. They have exceptional insulation characteristics, excellent stress control properties; long-term weather and regular wear and tear resistance, ease of installation and reliable performance in even in harshest of the situations.
These High performance 2:1 heat shrink material tubes, bundles, and protects cables; wire and hoses are used for a wide range of DIY applications. It is used extensively for cable and wire harnessing, strain relief, insulation, color-coding, identification, and protection.
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
ESP32 is a series of low-cost, low-power system on a chip microcontrollers with integrated Wi-Fi and dual-mode Bluetooth. The ESP32 series employs a Tensilica Xtensa LX6 microprocessor and includes built-in antenna switches, RF balun, power amplifier, low-noise receive amplifier, filters, and power-management modules. It is a successor to the ESP8266 microcontroller.
This TP4056 1A Li-ion lithium Battery Charging Module with Circuit Protection – Micro USB is a tiny module, perfect for charging single cells that don’t have their own protection circuit. Based on the TP4056 charger IC and DW01 battery protection IC this module will offer 5V 1A charge current then cut off when finished.
Furthermore when the battery voltage drops below 2.4V the protection IC will switch the load off to protect the cell from running at too low of a voltage – and also protects against over-voltage and reverse polarity connection (it will usually destroy itself instead of the battery) however please check you have it connected correctly the first time.
It is an 8 Channel Isolated 28V 10A Relay Module, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc. It is also able to control various appliances and other types of equipment with large current. Relay output maximum contact is AC250V 10A and DC 28V 10A. One can connect a microcontroller with standard interface directly to it. Red working status indicator lights are conducive to the safe use.
This Relay is used for wide variety of AC & DC applications like Home Automation configured, Solenoids, Motors, lights, fans, heavy load device, home appliances & controlling higher current loads from microcontroller development board.
PIR infrared sensor module is based on infrared technology. High sensitivity, high reliability, low power consumption, low voltage operation mode. It’s Compatible with ARDUINO, RASPBERRY PI, AVR, PIC, 8051, etc. Widely used in various auto-sensing electrical equipments for security, automation and lighting control systems because of its unique property of detecting the movement of infrared emitting objects like human bodies. This sensor is equipped with Fresnel lens for improving the detection pattern. All you have to do is give the supply voltage and leave for about a minute to stabilize. Any movement detection causes the sensor output to go high (3.3V). This sensor can be easily used for 220V automatic lighting systems with the help of a simple relay circuit.
These Jumper Wires are great for creating circuits between your microcontroller and the breadboard on the bots Reusable for fast build a prototype of an electronic circuit. Soldering is not required.
Wires are flexible, durable, reusable, easy to trace, easy to connect and disconnect.
With these Jumper wires you can modify or revise the circuits easily.