- -10%

These Jumper Wires are great for creating circuits between your microcontroller and the breadboard on the bots Reusable for fast build a prototype of an electronic circuit. Soldering is not required.
Wires are flexible, durable, reusable, easy to trace, easy to connect and disconnect.
With these Jumper wires you can modify or revise the circuits easily.
Features :
Package Includes :
4 x Flexible Female to Female Jumper Wires 20cm
A crystal oscillator is an electronic circuit or device which is used to generate a stable frequency with the help of a crystal instead of a tuned circuit. The crystal when vibrates, it acts like a resonator & as a result generates an oscillated frequency. The resonator circuit uses a crystal to generate the oscillation.
A crystal oscillator is an electronic circuit or device which is used to generate a stable frequency with the help of a crystal instead of a tuned circuit. The crystal when vibrates, it acts like a resonator & as a result generates an oscillated frequency. The resonator circuit uses a crystal to generate the oscillation.
These Jumper Wires are great for creating circuits between your microcontroller and the breadboard on the bots Reusable for fast build a prototype of an electronic circuit. Soldering is not required.
Wires are flexible, durable, reusable, easy to trace, easy to connect and disconnect.
With these Jumper wires you can modify or revise the circuits easily.
2N3904 is a general purpose and very popular NPN Transistor based on Silicon Epitaxial Planar Technology. This NPN transistor finds application in amplification and a simple switching circuit. It comes with a TO-92 package with very less noise. Its pins are compatible with through-hole assembly on PCB.
AMS1117-ADJ, 1A, Voltage Regulator IC is a series of low dropout three -terminal regulators with a dropout of adjustable voltage 1A load current. AMS 1117 features a very low standby current 2mA.
AMS 1117 offers thermal shut down and current limit functions, to assure the stability of chip and power system. And it uses a trimming technique to guarantee output voltage accuracy within 2%. Other output voltage accuracy can be customized on demand, such as 1%
This IC LM358 is 8-pin IC. These devices consist of two independent, high-gain frequency-compensated operational amplifiers designed to operate from a single supply or split supply over a wide range of voltages. Common-Mode Input Voltage Range Includes Ground, Allowing Direct Sensing Near Ground. Differential Input Voltage Range Equal to Maximum-Rated Supply Voltage: 32 V. Open-Loop Differential Voltage Gain is 100 dB.
AMS1117-3.3V, 1A, Voltage Regulator IC is a series of low dropout three -terminal regulators with a dropout of 3.3V at 1A load current. AMS 1117 features a very low standby current 2mA.
AMS 1117 offers thermal shut down and current limit functions, to assure the stability of chip and power system. And it uses a trimming technique to guarantee output voltage accuracy within 2%. Other output voltage accuracy can be customized on demand, such as 1%
Replacement of Heating Element for SMD Rework Station.
High heating rate so fast heating up, good insulating property, high efficiency and long life.
0402 capacitor is Mounted either by flow or reflow soldering methods and gives excellent dielectric strength due to uniform structure of dielectric layers
It is an RM065 100K Ohm Trimpot Trimmer Potentiometer. The potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver.
A diode is a device which allows current flow through only one direction. That is the current should always flow from the Anode to cathode.
This is called a power diode because of its high forward current and reverse voltage with a power dissipation of 6.25W. For 1N5408 Diode, the maximum current carrying capacity is 3A it withstand peaks up to 200A. Hence we can use this in circuits that are designed for less than 3A. The reverse current is 10uA which is negligible. These diodes have a slow recovery time so in modern electronics it is being replaced by other advanced diodes.
It is an RM065 500 Ohm Trimpot Trimmer Potentiometer. The potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver.
A crystal oscillator is an electronic circuit or device which is used to generate a stable frequency with the help of a crystal instead of a tuned circuit. The crystal when vibrates, it acts like a resonator & as a result generates an oscillated frequency. The resonator circuit uses a crystal to generate the oscillation.
1N4007 is a rectifier diode, designed specifically for circuits that need to convert alternating current to direct current. It can pass currents of up to 1 A, and have peak inverse voltage (PIV) rating of 1,000 V.
A crystal oscillator is an electronic circuit or device which is used to generate a stable frequency with the help of a crystal instead of a tuned circuit. The crystal when vibrates, it acts like a resonator & as a result generates an oscillated frequency. The resonator circuit uses a crystal to generate the oscillation.
0402 capacitor is Mounted either by flow or reflow soldering methods and gives excellent dielectric strength due to uniform structure of dielectric layers
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
These Jumper Wires are great for creating circuits between your microcontroller and the breadboard on the bots Reusable for fast build a prototype of an electronic circuit. Soldering is not required.
Wires are flexible, durable, reusable, easy to trace, easy to connect and disconnect.
With these Jumper wires you can modify or revise the circuits easily.