A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses.

These resistors are typical axial-lead metal film resistors, which have much better temperature stability than their carbon equivalents which provides lower noise and are generally better for high frequency or radio frequency applications.

A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses.

These resistors are typical axial-lead metal film resistors, which have much better temperature stability than their carbon equivalents which provides lower noise and are generally better for high frequency or radio frequency applications.

Small Size and light weight resistor which is suitable for both wave and reflow soldering leading to reduction in production costs.

Small Size and light weight resistor which is suitable for both wave and reflow soldering leading to reduction in production costs.

Heat Shrink Sleeve 15mm  are excellent for insulation. They have exceptional insulation characteristics, excellent stress control properties; long-term weather and regular wear and tear resistance, ease of installation and reliable performance in even in harshest of the situations.

These High performance 2:1 heat shrink material tubes, bundles, and protects cables; wire and hoses are used for a wide range of DIY applications. It is used extensively for cable and wire harnessing, strain relief, insulation, color-coding, identification, and protection.

In the instance of circuit failure or abnormalcy, with rising current, the increased current in the circuit may damage the device or important components or even burning of the circuit which may cause a fire. 

The fuse breaks the circuit if a fault in an appliance causes too much current to flow. This protects the wiring and the appliance if something goes wrong. The fuse contains a piece of wire that melts easily. If the current going through the fuse is too much, the wire heats up until it melts and breaks the circuit. Thus play a role in the safe operation of the protection circuit.

A crystal oscillator is an electronic circuit or device which is used to generate a stable frequency with the help of a crystal instead of a tuned circuit. The crystal when vibrates, it acts like a resonator & as a result generates an oscillated frequency. The resonator circuit uses a crystal to generate the oscillation.

A diode is a device which allows current flow through only one direction. That is the current should always flow from the Anode to cathode.

This is called a power diode because of its high forward current and reverse voltage with a power dissipation of 6.25W. For 1N5408 Diode, the maximum current carrying capacity is 3A it withstand peaks up to 200A. Hence we can use this in circuits that are designed for less than 3A.  The reverse current is 10uA which is negligible. These diodes have a slow recovery time so in modern electronics it is being replaced by other advanced diodes.

It is an RM065 20K Ohm Trimpot Trimmer Potentiometer.  The potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver.

0402 capacitor is Mounted either by flow or reflow soldering methods and gives excellent dielectric strength due to uniform structure of dielectric layers 

Small Size and light weight resistor which is suitable for both wave and reflow soldering leading to reduction in production costs.

A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses.

These resistors are typical axial-lead metal film resistors, which have much better temperature stability than their carbon equivalents which provides lower noise and are generally better for high frequency or radio frequency applications.

A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses.

These resistors are typical axial-lead metal film resistors, which have much better temperature stability than their carbon equivalents which provides lower noise and are generally better for high frequency or radio frequency applications.

0402 capacitor is Mounted either by flow or reflow soldering methods and gives excellent dielectric strength due to uniform structure of dielectric layers 

Small Size and light weight resistor which is suitable for both wave and reflow soldering leading to reduction in production costs.

A ceramic capacitor is a fixed-value capacitor where the ceramic material acts as the dielectric. It is constructed of two or more alternating layers of ceramic and a metal layer acting as the electrodes. The composition of the ceramic material defines the electrical behavior and therefore applications.