- -40%

A crystal oscillator is an electronic circuit or device which is used to generate a stable frequency with the help of a crystal instead of a tuned circuit. The crystal when vibrates, it acts like a resonator & as a result generates an oscillated frequency. The resonator circuit uses a crystal to generate the oscillation.
Specifications:
Package Contents:
1 Piece X 11.0592Mhz Passive Quartz Resonator Crystal Oscillator
Replacement of Heating Element for SMD Rework Station.
High heating rate so fast heating up, good insulating property, high efficiency and long life.
A diode is a device which allows current flow through only one direction. That is the current should always flow from the Anode to cathode.
This is called a power diode because of its high forward current and reverse voltage with a power dissipation of 6.25W. For 1N5408 Diode, the maximum current carrying capacity is 3A it withstand peaks up to 200A. Hence we can use this in circuits that are designed for less than 3A. The reverse current is 10uA which is negligible. These diodes have a slow recovery time so in modern electronics it is being replaced by other advanced diodes.
A crystal oscillator is an electronic circuit or device which is used to generate a stable frequency with the help of a crystal instead of a tuned circuit. The crystal when vibrates, it acts like a resonator & as a result generates an oscillated frequency. The resonator circuit uses a crystal to generate the oscillation.
This IC LM358 is 8-pin IC. These devices consist of two independent, high-gain frequency-compensated operational amplifiers designed to operate from a single supply or split supply over a wide range of voltages. Common-Mode Input Voltage Range Includes Ground, Allowing Direct Sensing Near Ground. Differential Input Voltage Range Equal to Maximum-Rated Supply Voltage: 32 V. Open-Loop Differential Voltage Gain is 100 dB.
It is an RM065 20K Ohm Trimpot Trimmer Potentiometer. The potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver.
The 1N5819 is a Schottky Diode with forward voltage drop of 600mV and a forward current of 1A. Since it has a very low forward voltage drop it can be used in reverse polarity protection circuits, unlike a normal diode which has more than 1V as forward voltage drop 1N5819 only has 600mV drop across it when 1A current is flowing through it.
Compared to normal diodes Schottky diode also has relatively faster switching speeds and hence can be used in high frequency switching circuits. The reverse blocking voltage for 1N5819 is about 28V only which is kind of a downside for all Schottky diodes so make sure this does not affect the performance in your circuit.
It is an RM065 5K Ohm Trimpot Trimmer Potentiometer. The potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver.
A crystal oscillator is an electronic circuit or device which is used to generate a stable frequency with the help of a crystal instead of a tuned circuit. The crystal when vibrates, it acts like a resonator & as a result generates an oscillated frequency. The resonator circuit uses a crystal to generate the oscillation.
These Jumper Wires are great for creating circuits between your microcontroller and the breadboard on the bots Reusable for fast build a prototype of an electronic circuit. Soldering is not required.
Wires are flexible, durable, reusable, easy to trace, easy to connect and disconnect.
With these Jumper wires you can modify or revise the circuits easily.
This is a silicon rectifier diode with high current capability. 1N5399 diode has a cathode (-) and anode (+). In the schematic symbol, the tip of the triangle with the line on top of it is the cathode. The cathode is marked on the body of a diode by a band.Diode polarity Current can flow from the anode to the cathode only and never from the cathode to the anode - 1N5399 diode is like a one way valve.
Heat Shrink Sleeve 15mm are excellent for insulation. They have exceptional insulation characteristics, excellent stress control properties; long-term weather and regular wear and tear resistance, ease of installation and reliable performance in even in harshest of the situations.
These High performance 2:1 heat shrink material tubes, bundles, and protects cables; wire and hoses are used for a wide range of DIY applications. It is used extensively for cable and wire harnessing, strain relief, insulation, color-coding, identification, and protection.
It is an RM065 1M Ohm Trimpot Trimmer Potentiometer. The potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver.
It is an RM065 500 Ohm Trimpot Trimmer Potentiometer. The potentiometer is easy to mount on a PCB and can be adjusted using a screwdriver.
A crystal oscillator is an electronic circuit or device which is used to generate a stable frequency with the help of a crystal instead of a tuned circuit. The crystal when vibrates, it acts like a resonator & as a result generates an oscillated frequency. The resonator circuit uses a crystal to generate the oscillation.
1N4007 is a rectifier diode, designed specifically for circuits that need to convert alternating current to direct current. It can pass currents of up to 1 A, and have peak inverse voltage (PIV) rating of 1,000 V.
A crystal oscillator is an electronic circuit or device which is used to generate a stable frequency with the help of a crystal instead of a tuned circuit. The crystal when vibrates, it acts like a resonator & as a result generates an oscillated frequency. The resonator circuit uses a crystal to generate the oscillation.
A crystal oscillator is an electronic circuit or device which is used to generate a stable frequency with the help of a crystal instead of a tuned circuit. The crystal when vibrates, it acts like a resonator & as a result generates an oscillated frequency. The resonator circuit uses a crystal to generate the oscillation.